Goodbye JET Jointer

Last weekend I said goodbye to my JET 6" jointer watching it go down the drivechoice in the back of its new owners truck. Though I considered my woodworking habits to be "blended" I found that I still relied on the power tools more than I liked and with the encouragement of others, I have decided to make turn around the corner to going unplugged. The table saw is next, it is listed for sale, that leaves me with a Dewalt 13" planer, a Delta 14" band saw, a Delta dust collector, Rikon lathe, and a Ryobi drill press. The planer would be next, I think I will keep the band saw, lathe, and the drill press for work outside the shop.  I have an almost full arsenal of saws, sharp, and ready, a nice selection of hand planes collected over the years, also sharp and ready. I will be selling some of the planes that are duplicates.It was strange watching that jointer leave the shop, I used it off an on probably for the last 8 years or so, but it is being replaced with a very nice 30" wooden jointer plane,  and since I have been doing a lot of the work lately with hand tools, the conversion doesnt seem as scary as I thought. The tables you see in the post below were made using hand cut mortise and tenons, the tops and shelves fiished with hand planes, and the inner drawer supports cut by hand.So off I go taking one step closer to the quiet, and safer, side of working wood, perhaps making less dust and mess, feeling more connected to the work, and enjoying it a lot more in this phase of the journey.?

Read More..

Goodbye Old Friend

My college graduation gift was the Porter-Cable 1-1/2 HP router kit. It came with a single motor, a D-handle base, a plunge base & a small router table. It was my first power tool. While it still serves me well, Ive moved on to bigger routers with soft starts and dust collection. Router technology improved, and so did my collection.

The DeWalt 12" Dual-Bevel Sliding
Compound Miter Saw.

A few months later the first power tool I bought myself was a DeWalt 12" Dual-Bevel Sliding Compound Miter saw. I bought it at Home Depot when my wife and I went into closing on our first house (how, after all, can anyone work on their house with a 12" dual-bevel sliding compound miter saw?). Once in the house, I built a bench for the saw. That was in early 2001. The bench was 10 long and 37" deep to accommodate the travel of the saws rails. It served as a miter saw bench, a work bench and an assembly table.

The DeWalt takes up 37" from the
front of the handle when turned in
to the back of the rails.

Two years ago when we moved and my shop was squeezed into a 911" x 22 single car garage, the 37" deep bench became un-workable. There was just no choice I could give up all that space along a wall. Shortly after moving I sold the bench and the 3 custom made rolling carts that fit underneath it to one of my co-workers. The saw stayed with me. It spent most time folded up in the corner. I had to unfolded it and set it on a folding table in the drivechoice for work.
Ive known that the depth of the big old DeWalt was too much for the new shop, but when compared to the newer saws on the market today with less rear projection, I didnt see the same types of improvements as occurred in routers. I still think my 10 year old DeWalt is nicer than most saws on the market.

Packed & Ready to go.

My hesitation in replacing the DeWalt ended this week when we needed a saw at work to crosscut 12" wide strips of plywood for the 100 or so custom curbs were building for the skylights on a condo re-roof project were doing. I immediately offered up my 12" DeWalt, Forest Chopmaster and all. Work bought it with no haggling and the DeWalt quickly set to work making skylight curbs.
Now I approach a weekend of home improvement (PVC fascia & window trim installation) with no miter saw. Im not sure how Ill do it. Using a track saw to cross cut 16 PVC 1x6s to length seems the most accurate choice left to me and also like so much more work than with a miter saw. To remedy the situation Ill be scoping out miter saws at Woodworking in America next week (thankfully theyve added power tools this year). I know Festool will be there with a Kapex and Im hoping the new Bosch Gliding Miter Saw will make an appearance. Ill cross reference them both against the new Makitas and hopefully one will come out a winner. Then my shop wont feel so empty.

My old saw in her new home.

What power tool do you feel lost without?

Read More..